Carbon Fiber

Carbon Fiber

Flame Retardant - Preliminary Datasheet

Carbon Fiber

Sultron™ Polysulfone PSU is a translucent material that offers a combination of excellent mechanical, thermal, and electrical properties. This grade often replaces polycarbonate whenever higher temperature resistance, improved chemical resistance, or autoclavability is required. Sultron™ PSU shapes are ideal for analytical instrumentation, medical devices, and semiconductor process equipment components due to their outstanding radiation stability, and resistance to acidic and salt solutions, detergents, hot water, and steam.

Typical characteristics - High rigidity at good dimensional stability - Very high continuous service temperature - Very good hydrolysis resistance - Hardly inflammable - Self-extinguishing - Very low smoke development - Good resistance against high energy radiation - High tensile strength - High hardness - Good machinability - Good adhesive properties - Very good weldability - Low coefficient of thermal expansion - Very good electrical insulation properties - Exceptionally low radiation absorption in the microwave range - Good thermoformability Typical industries - Electronics - Bakery and Confectionery - Meat, Fish and Poultry Processing - Beverage Industry - Healthcare - Food Industry - Mechanical Engineering Industry - Electrical Industry

TECASON ® S natural - Stock Shapes (rods, plates, tubes) Main features - high thermal and mechanical capacity - good chemical resistance - high creep resistance - high strength - autoclavable Target Industries - medical technology - electronics - pharmaceutical industry - semiconductor technology - food engineering - food processing

Thermalux® Polysulfone (PSU) is an amber colored, semi-transparent, heat-resistant, high performance engineering thermoplastic that offers higher heat resistance and better hydrolytic stability than polycarbonate (PC). It retains its good mechanical properties when exposed to steam and other sterilization techniques.

Polysulfone natural is transparent and can be offered in any color.

Data was measured on natural colored test specimens.

UDEL GF- 110树脂是一种10％玻纤增强聚砜（PSU）。玻纤极大提高了聚砜树脂的刚性、拉伸强度、耐蠕变性、尺寸稳定性和耐化学性。卓越的性能和极具吸引力的价格使这些树脂在许多工程应用成为有效的金属替代材料。 -黑色： Udel GF-110 Bk 937 - 灰色：Udel GF-110 GY 8057 - 本色： Udel GF-110 NT - 本色： Udel GF-110 NT LE

UDEL GF- 120树脂是一种20％玻纤增强聚砜。玻纤极大提高了聚砜树脂的刚性、拉伸强度、耐蠕变性、尺寸稳定性和耐化学性。卓越的性能和极具吸引力的价格使这些树脂在许多工程应用成为有效的金属替代材料。 - 黑色： Udel GF-120 Bk 937 - 黑色：Udel GF-120 BK 937 - 本色： Udel GF-120 NT - 灰色：Udel GF-120 GY 1234

Udel® GF-130, resin is a 30% glass fiber reinforced polysulfone compound. Glass fiber substantially increases the rigidity, tensile strength, creep resistance, dimensional stability and chemical resistance of the polysulfone resin. The high performance properties and attractive price make these resins particularly effective alternatives to metals in many engineering applications.

Udel P-1700 LCD 聚砜特别适合用于制造多孔膜过滤产品。这类膜通常呈中空纤维形式，但也采用管、板或螺旋缠绕形式。被用于各种应用，如饮用水处理、废水处理、血液处理、制药纯化、气体分离、乳品加工和各类食品加工。 膜生产商可以采用市售偶极非质子传递溶剂，如二甲基乙酰胺（ DMAC ） 、二甲基甲酰胺（DMF）和N-甲基吡咯烷酮（NMP）对该树脂进行很好的溶解，在水中完全混溶，并可以很好地控制孔径大小和孔径分布，获得高的膜强度和良好成膜性能。 普通牌号的聚砜含有能从溶液中析出、从而堵塞处理过滤器、限制掺杂溶液寿命的环状二聚物。Udel P-1700 NT LCD是一种专门生产的环状二聚物含量水平较低的树脂，给定重均分子量(Mw)具有较高的数均分子量（Mn），从而导致较高的纤维强度，也即，纤维断裂少、表面缺陷少、废品少。 所得到的膜具有优异的水解稳定性，适应2～13的PH值环境。耐受各种清洗方式，包括盐酸或氢氧化钠。该树脂的Tg为185 ℃，显示出高耐热性。 - 透明： Udel P-1700 NT LCD

Udel® P-1700 polysulfone (PSU) is a tough, rigid, high-strength thermoplastics suitable for continuous use up to 300°F (149°C). It is resistant to oxidation and hydrolysis and withstand prolonged exposure to high temperatures and repeated sterilization. Udel® P-1700 polysulfone is highly resistant to mineral acids, alkali and salt solutions. Resistance to detergents and hydrocarbon oils is good, but the resin may be attacked by polar solvents such as ketones, chlorinated hydrocarbons and aromatic hydrocarbons. These resins are also highly resistant to degradation by gamma or electron beam radiation. Electrical properties of Udel® P-1700 polysulfones are stable over a wide temperature range and after immersion in water or exposure to high humidity. The resins comply with FDA 21 CFR 177.1655 and may be used in articles intended for repeated use in contact with foods. Additionally, they are approved by the NSF, by the Department of Agriculture for contact with meat and poultry and by the 3-A Sanitary Standards of the Dairy Association. - Transparent: Udel® P-1700 CL 2611 CMP - Transparent: Udel® P-1700 CL 2611 CMP MR - Transparent: Udel® P-1700 NT 06 - Transparent: Udel® P-1700 NT 11 - Transparent: Udel® P-1700 NT 11 MR - Opaque Black : Udel® P-1700 BK 937 - Opaque White: Udel® P-1700 WH 6417 - Opaque White: Udel® P-1700 WH 7407 - Opaque Gray: Udel® P-1700 GY 8057

UDEL P- 1710聚砜（PSU）是一种具有高韧度、刚性、高强度的热塑性塑料，适合在高达300 °F（149 °C）的温度条件下连续使用。该树脂抗氧化、抗水解，可长时间暴露于高温度环境，并进行反复消毒。 UDEL P- 1710聚砜极耐无机酸、碱和盐溶液，并具有良好的耐洗涤剂和碳氢油类物质，但容易受到极性溶剂如酮、氯代烃类和芳族烃的腐蚀。 该树脂同时极耐γ射线或电子束辐射降解。在各种温度范围下、浸渍在水中或在高度潮湿的环境下，具有稳定的电性能。 - 本色： UDEL P- 1710 NT 15

Udel聚砜是一种高韧度、高刚性、高强度的热塑性塑料，具有出色的耐水解性。Udel P-3500 LCD MB系列聚合物特别适用于溶剂型工艺生产多孔中空纤维、平片膜。这些高分子量聚合物被用于各种膜过滤产品，如肾透析、水处理、生物处理、食品和饮料加工、工业气体分离。 Udel聚砜聚合物具有许多膜工业行业所需性能，如优异的机械性能、在2～132PH值条件下稳定、优异的耐腐蚀性和良好的耐中等浓度氯的性能 。是析出水平低、不溶解材料，适用于饮用水和与食品接触的产品。可用蒸汽、环氧乙烷和电子束辐射消毒。 Udel P-3500 LCD MB系列聚合物包含一系列窄分子量分布的牌号，如下图所示。各牌号环状二聚体水平要低于原来的P-3500NT 11牌号 。这在溶液处理，如膜生产工艺中非常重要重要，因为它提高了纺丝原液的溶液稳定性、减少了设备的结垢。

Udel® P-3500 NT LCD is a very high molecular weight grade of polysulfone, and therefore offers the greatest toughness and chemical resistance of the available grades. It is well-suited for extrusion. Polysulfone is a tough, rigid and transparent high-strength thermoplastic that is suitable for long-term use up to 300°F (149°C). It is resistant to oxidation and hydrolysis and withstands prolonged exposure to high temperatures and repeated sterilization. Polysulfone is resistant to mineral acids, alkali, salt solutions, detergents and hydrocarbon oils. Contact with polar solvents such as ketones, chlorinated hydrocarbons and aromatic hydrocarbons should be avoided, as these types of chemical compounds can cause stress cracking or solvate polysulfone resin. Polysulfone is highly resistant to degradation by gamma or electron beam radiation but can be adversely affected by long term exposure to ultraviolet. Electrical properties of the polymer are very stable over a wide range of temperatures and after immersion in water or exposure to high humidity. The resin is very safe for food contact uses. It complies with FDA 21 CFR 177, 1655 and may be used in articles intended for repeated use in contact with foods. Additionally, it is approved by the NSF, by the Department of Agriculture for contact with meat and poultry and the 3-A Sanitary Standards of the Dairy Association.

Udel® P-3703 is a high-flow grade of polysulfone intended for injection molding applications with thin walls or long flow lengths. This grade has higher flow than Udel® P-1700 and a slightly greater tendency to stress crack in some aggressive environments. Udel® polysulfone is a tough, rigid, high-strength thermoplastic that maintains its properties at temperatures from -101°C to 149°C (-150°F to 300°F). The heat deflection temperature at 1.8 MPa (264 psi) is 174°C (345°F). For most purposes, this resin is suitable for continuous use up to 149°C (300°F). The material is resistant to oxidation and hydrolysis and withstands prolonged exposure to high temperatures and repeated sterilization. Udel polysulfone is highly resistant to mineral acids, alkali and salt solutions. The resistance to detergents and hydrocarbon oils is good, but it will be attacked by polar solvents such as ketones, chlorinated hydrocarbons and aromatic hydrocarbons. Electrical properties of Udel polysulfone are stable over a wide temperature range and after immersion in water or exposure to high humidity. - Natural: Udel® P-3703 NT 11

Ultrason S 2010 G4 is a 20% glass reinforced, medium viscosity injection molding PSU grade with high rigidity and strength. Applications Typical applications include circuit braker parts, lamp holders, heat shields, impellers, and printer cartridges.

Ultrason S 2010 G6 is a 30% glass reinforced, medium viscosity injection molding PSU grade with high rigidity and strength. Applications Typical applications include circuit braker parts, lamp holders, heat shields, impellers, and printer cartridges.

Ultrason S 2010 is an unreinforced, medium viscosity standard injection molding PSU grade. It flows readily and offers outstanding heat resistance and dimensional stability. Typical applications include automotive applications such as fuse encapsulation, connectors, heating system and headlight components and household applications requiring high heat resistance.

Unreinforced, higher viscosity injection moulding and extrusion grade, tougher, with improved chemical resistance and demolding optimized.

Ultrason S 3010 MR is an unreinforced higher viscosity injection molding grade with improved toughness and chemical resistance (stress crack resistance).

Ultrason S 3010 is medium viscosity injection molding grade with improved toughness and chemical resistance (stress crack resistance). Applications Typical applications include laboratory accessories and household parts.

Ultrason S 6010 is a high molecular weight injection molding and extrusion grade with excellent chemical resistance (stress crack resistance) and good solubility in typical solvents (N-methylpyrrolidone, dimethlyacetamide, dicholormethane) used in the production of membranes or coatings. Applications Typical applications include sanitary and heating systems/parts and membranes.

UNIFONE PSU (Polysulfone) is an amorphous high performance thermoplastic material that has proven performance at elevated temperatures. Good mechanical properties along with thermal stability allow for its use in load bearing applications over broad temperature ranges. Other notable attributes include flame retardance, excellent radiation resistance, and good chemical resistance. The ability of UNIFONE PSU to withstand common sterilization techniques supports its use in numerous sanitary applications such as medical instruments and food processing machinery. Nytef Plastic's UNIFONE PSU stock shapes are amber in color and semi-transparent. They machine easily and are available in a full range of heavy gauge rod, plate and tubular bar sizes. PRODUCT ATTRIBUTES - 320°F continuous use temperature - Excellent strength and rigidity, even at elevated temperatures - High impact resistance - Low moisture absorption - Chemically resistant to many acids and solvents - Superior electrical properties - Rated UL V-0 - Gamma radiation resistance - Easily machined and fabricated INDUSTRIES - Medical - Pharmaceutical manufacturing - Aircraft and aerospace - Appliance manufacturing - Electrical and electronics manufacturing - Food processing APPLICATIONS - Manifolds - Electrical insulators, connectors, and components - Aircraft instrumentation - Medical instruments and instrument trays - Sensors and analytical instruments - Microwave cookware

PSU resin unfilled for injection moulding

UL 94 V2, halogen free, excellent aesthetics.

PSU resin, 30% glass fiber reinforced for injection moulding