Mold Star™ 14T, 19T, 20T and 31T are easy to use translucent platinum cure silicones that are mixed 1A:1B by volume (no weighing scale necessary). They feature a relatively low viscosity and vacuum degassing is not required for most applications. Mold Star™ T Series silicone cures to a soft, strong rubber that is tear resistant and exhibits very low long term shrinkage. Molds made with Mold Star™ silicone will last a long time in your mold library and are good for casting wax, gypsum, resins, and other materials. An infinite number of color effects can be achieved by adding Silc Pig™ silicone pigments or Cast Magic™ effects powders. Mold Star™ T Series silicones are heat resistant up to 450°F (232°C) and are suitable for casting low-temperature melt metal alloys. Note: This product will not cure against surfaces containing sulfur, even when sealed. Cured Mold Star™ T Series silicones have been tested and certified skin safe by an independent laboratory.

Mold Star™ rubbers are easy to use platinum silicones which are mixed 1A:1B by volume (no weighing scale necessary). Mold Star™ silicones feature relatively low viscosities and vacuum degassing is not required for most applications. The pot life of Mold Star™ 15 SLOW is 50 minutes and cure time is 4 hours at room temperature. Mold Star™ 16 FAST is a faster material with a 6 minute pot life and 30 minute cure time. Mold Star™ 30 is a harder material, with a 30A Shore hardness Mold Star™ silicones cure to soft, strong rubbers which are tear resistant and exhibit very low long term shrinkage. Molds made with Mold Star™ will last a long time in your mold library and are good for casting wax, gypsum, resins, concrete and other materials. Cured Mold Star™ rubber is heat resistant up to 450°F (232°C) and is suitable for casting low-temperature melt metal alloys. Note: Mold Star™ rubbers are not intended for brush-on moldmaking.

Mold Star™ rubbers are easy to use platinum silicones which are mixed 1A:1B by volume (no weighing scale necessary). Mold Star™ silicones feature relatively low viscosities and vacuum degassing is not required for most applications. The pot life of Mold Star™ 15 SLOW is 50 minutes and cure time is 4 hours at room temperature. Mold Star™ 16 FAST is a faster material with a 6 minute pot life and 30 minute cure time. Mold Star™ 30 is a harder material, with a 30A Shore hardness Mold Star™ silicones cure to soft, strong rubbers which are tear resistant and exhibit very low long term shrinkage. Molds made with Mold Star™ will last a long time in your mold library and are good for casting wax, gypsum, resins, concrete and other materials. Cured Mold Star™ rubber is heat resistant up to 450°F (232°C) and is suitable for casting low-temperature melt metal alloys. Note: Mold Star™ rubbers are not intended for brush-on moldmaking.

Mold Star™ 14T, 19T, 20T and 31T are easy to use translucent platinum cure silicones that are mixed 1A:1B by volume (no weighing scale necessary). They feature a relatively low viscosity and vacuum degassing is not required for most applications. Mold Star™ T Series silicone cures to a soft, strong rubber that is tear resistant and exhibits very low long term shrinkage. Molds made with Mold Star™ silicone will last a long time in your mold library and are good for casting wax, gypsum, resins, and other materials. An infinite number of color effects can be achieved by adding Silc Pig™ silicone pigments or Cast Magic™ effects powders. Mold Star™ T Series silicones are heat resistant up to 450°F (232°C) and are suitable for casting low-temperature melt metal alloys. Note: This product will not cure against surfaces containing sulfur, even when sealed. Cured Mold Star™ T Series silicones have been tested and certified skin safe by an independent laboratory.

Mold Star™ 14T, 19T, 20T and 31T are easy to use translucent platinum cure silicones that are mixed 1A:1B by volume (no weighing scale necessary). They feature a relatively low viscosity and vacuum degassing is not required for most applications. Mold Star™ T Series silicone cures to a soft, strong rubber that is tear resistant and exhibits very low long term shrinkage. Molds made with Mold Star™ silicone will last a long time in your mold library and are good for casting wax, gypsum, resins, and other materials. An infinite number of color effects can be achieved by adding Silc Pig™ silicone pigments or Cast Magic™ effects powders. Mold Star™ T Series silicones are heat resistant up to 450°F (232°C) and are suitable for casting low-temperature melt metal alloys. Note: This product will not cure against surfaces containing sulfur, even when sealed. Cured Mold Star™ T Series silicones have been tested and certified skin safe by an independent laboratory.

Mold Star™ rubbers are easy to use platinum silicones which are mixed 1A:1B by volume (no weighing scale necessary). Mold Star™ silicones feature relatively low viscosities and vacuum degassing is not required for most applications. The pot life of Mold Star™ 15 SLOW is 50 minutes and cure time is 4 hours at room temperature. Mold Star™ 16 FAST is a faster material with a 6 minute pot life and 30 minute cure time. Mold Star™ 30 is a harder material, with a 30A Shore hardness Mold Star™ silicones cure to soft, strong rubbers which are tear resistant and exhibit very low long term shrinkage. Molds made with Mold Star™ will last a long time in your mold library and are good for casting wax, gypsum, resins, concrete and other materials. Cured Mold Star™ rubber is heat resistant up to 450°F (232°C) and is suitable for casting low-temperature melt metal alloys. Note: Mold Star™ rubbers are not intended for brush-on moldmaking.

Mold Star™ 14T, 19T, 20T and 31T are easy to use translucent platinum cure silicones that are mixed 1A:1B by volume (no weighing scale necessary). They feature a relatively low viscosity and vacuum degassing is not required for most applications. Mold Star™ T Series silicone cures to a soft, strong rubber that is tear resistant and exhibits very low long term shrinkage. Molds made with Mold Star™ silicone will last a long time in your mold library and are good for casting wax, gypsum, resins, and other materials. An infinite number of color effects can be achieved by adding Silc Pig™ silicone pigments or Cast Magic™ effects powders. Mold Star™ T Series silicones are heat resistant up to 450°F (232°C) and are suitable for casting low-temperature melt metal alloys. Note: This product will not cure against surfaces containing sulfur, even when sealed. Cured Mold Star™ T Series silicones have been tested and certified skin safe by an independent laboratory.